alarm sensor problems

[martyn812]

having problems with alarm siren i have no permanent power to wire 3 it should be 12v constant rigged up a wire to fuse now alarm works but not sensors codes are below before wire added
ddress 46: Central Conv. Labels: 1K0-959-433-MAX.clb
Part No SW: 1K0 959 433 BT HW: 1K0 959 433 BT
Component: KSG PQ35 G2 020 0205
Revision: 00020000 Serial number: 00000000000000
Coding: 81900A0002830C7F3F040F0FF0085ACE103C00
Shop #: WSC 00020 790 12345
VCID: 8305E987C2E04306091-80D6

Subsystem 1 - Component: Sounder No Answer

Subsystem 2 - Component: NGS No Answer

Subsystem 3 - Component: IRUE No Answer

3 Faults Found:
01135 - Interior Monitoring Sensors
004 - No Signal/Communication
Freeze Frame:
Fault Status: 01100100
Fault Priority: 4
Fault Frequency: 1
Reset counter: 63
Mileage: 113668 km
Time Indication: 0
Date: 2040.14.14
Time: 12:19:03

00323 - Vehicle Inclination Sensor (G384)
004 - No Signal/Communication
Freeze Frame:
Fault Status: 01100100
Fault Priority: 4
Fault Frequency: 1
Reset counter: 63
Mileage: 113668 km
Time Indication: 0
Date: 2040.14.14
Time: 12:19:03

01134 - Alarm Horn (H12)
004 - No Signal/Communication
Freeze Frame:
Fault Status: 01100100
Fault Priority: 4
Fault Frequency: 1
Reset counter: 63
Mileage: 113668 km
Time Indication: 0
Date: 2040.14.14
Time: 12:19:03
after wire added
Address 46: Central Conv. Labels: 1K0-959-433-MAX.clb
Part No SW: 1K0 959 433 BT HW: 1K0 959 433 BT
Component: KSG PQ35 G2 020 0205
Revision: 00020000 Serial number: 00000000000000
Coding: 81900A0002830C7F3F040F0FF0085ACE101C00
Shop #: WSC 00020 790 12345
VCID: 8305E987C2E04306091-80D6

Subsystem 1 - Part No: 1K0 951 605 C
Component: LIN BACKUP HORN H05 1501

Subsystem 2 - Component: NGS No Answer

Subsystem 3 - Component: IRUE No Answer

2 Faults Found:
01135 - Interior Monitoring Sensors
004 - No Signal/Communication
Freeze Frame:
Fault Status: 01100100
Fault Priority: 4
Fault Frequency: 1
Reset counter: 72
Mileage: 113877 km
Time Indication: 0
Date: 2040.14.23
Time: 16:18:38

00323 - Vehicle Inclination Sensor (G384)
004 - No Signal/Communication
Freeze Frame:
Fault Status: 01100100
Fault Priority: 4
Fault Frequency: 1
Reset counter: 72
Mileage: 113877 km
Time Indication: 0
Date: 2040.14.23
Time: 16:18:38

must be aplace they all link up before going to sensor

[Cuprabob]

There is a button on the driver's side B Pillar that you push when you exit the car to disable the interior sensors, so that may be worth a look. Not sure whether the "tilt" sensor is controlled by it though.

Also double clicking the keyfob when locking disables the deadlocks and the alarm, if my memory serves me right, so that may be another route to follow.

You might just be getting the fault codes as there is no power to the siren.

[martyn812]

thanks checked button but no differance will check locking its powered by a hot wire at the moment so need to know why the powers gone maybe a relay somewhere.