RNS 510 not communicating with car
Posted: Wed Jan 26, 2011 2:52 pm
I installed RNS 510 to my scirocco 3 months ago, but suddenly some issues appeared.
RNS doesn't power on/off along with car ignition, MFD doesn't show any information from unit, steering wheel buttons doesn't work.
VCDS informs that there's no signal:
01305 - Databus for Infotainment
004 - No Signal/Communication
Freeze Frame
Fault Status: 01100100
Fault Priority: 1
Fault Frequency: 2
Reset counter: 247
01300 - Control Module for Navigation with CD-Rom (J401)
004 - No Signal/Communication
Freeze Frame
Fault Status: 01100100
Fault Priority: 2
Fault Frequency: 1
Reset counter: 247
01304 - Radio
004 - No Signal/Communication
Freeze Frame
Fault Status: 01100100
Fault Priority: 2
Fault Frequency: 1
Reset counter: 247
Otherwise it's working fine: unit can be turned on/off with the button in front, navigation's ok etc.
Though I noticed one weird thing today during 1hour drive, unit suddenly just went down two times. After pressing power button it was instantly back alive and music playback continued.
Any ideas what are the most common reasons for RNS 510 not communicating with car/can bus?
And do you possibly have any information regarding "CAN" menu under the 'hidden' service menu?
I'm curious because yesterday I checked and the overall status was "no communication". At this point I disconnected the unit & tried original RCD300 which was perfect.
Next I deleted radio & navigation with VCDS and installed RNS510. After that there was something else (can't remember for sure, maybe "off"..) in service/CAN menu instead of "no communication", but still no co-operation with car.
Is there any possibility that scirocco would "find" the rns 510 without coding via VCDS?
I'll surely re-select radio & nav with VCDS as soon as possible, but I would like to hear your comments & experiences with similar problems. Thanks!
While writing this I thought that perhaps the reason could be in quadlock, if some wires are not properly connected.
If I disconnect the unit once more -> press the wires more firmly -> install radio & navigation with VCDS -> connect RNS => should the unit work immediately?
Reboot is most likely needed but do I have to wait couple of minutes e.g. for MFD screen to turn off or so?
RNS doesn't power on/off along with car ignition, MFD doesn't show any information from unit, steering wheel buttons doesn't work.
VCDS informs that there's no signal:
01305 - Databus for Infotainment
004 - No Signal/Communication
Freeze Frame
Fault Status: 01100100
Fault Priority: 1
Fault Frequency: 2
Reset counter: 247
01300 - Control Module for Navigation with CD-Rom (J401)
004 - No Signal/Communication
Freeze Frame
Fault Status: 01100100
Fault Priority: 2
Fault Frequency: 1
Reset counter: 247
01304 - Radio
004 - No Signal/Communication
Freeze Frame
Fault Status: 01100100
Fault Priority: 2
Fault Frequency: 1
Reset counter: 247
Otherwise it's working fine: unit can be turned on/off with the button in front, navigation's ok etc.
Though I noticed one weird thing today during 1hour drive, unit suddenly just went down two times. After pressing power button it was instantly back alive and music playback continued.
Any ideas what are the most common reasons for RNS 510 not communicating with car/can bus?
And do you possibly have any information regarding "CAN" menu under the 'hidden' service menu?
I'm curious because yesterday I checked and the overall status was "no communication". At this point I disconnected the unit & tried original RCD300 which was perfect.
Next I deleted radio & navigation with VCDS and installed RNS510. After that there was something else (can't remember for sure, maybe "off"..) in service/CAN menu instead of "no communication", but still no co-operation with car.
Is there any possibility that scirocco would "find" the rns 510 without coding via VCDS?
I'll surely re-select radio & nav with VCDS as soon as possible, but I would like to hear your comments & experiences with similar problems. Thanks!
While writing this I thought that perhaps the reason could be in quadlock, if some wires are not properly connected.
If I disconnect the unit once more -> press the wires more firmly -> install radio & navigation with VCDS -> connect RNS => should the unit work immediately?
Reboot is most likely needed but do I have to wait couple of minutes e.g. for MFD screen to turn off or so?