Scirocco Central

Hi all,

Over the weekend I noticed one of my wipers is damaged and just flapping in the wind. Can anyone recommend what to replace the front wipers with? Pref on Amazon as can get them next day.

Thanks

Bosch, Valeo

I picked up a pair of Bosch A980s for about £20.00 on Amazon inc postage a couple of weeks ago.

Xtreme Auto Accessories

Valeo VM331 or Bosch A980S for a pair of fronts.

Bosch A251H for the rear blade.

I fitted the bosch three years in and its lasted a lot longer than the original blades for some reason. I suppose there may have been a bad winter and the old ones froze on at some point [SMILING FACE WITH OPEN MOUTH AND SMILING EYES]. Anyway I recommend bosch.

Sent from my SM-G928F using Tapatalk

Was searching for new wipers & found this thread. Went with:

- Bosch A980S (Front)
- Bosch A330H (Rear)

Front wipers have arrived & the connector point & serial numbers are different from new to old (pics attached).

Is this not the right blade? Or am I missing something? The connectors are similar in places but are clearly different, didn’t want to force it incase it broke.

Top blade - old blade
Bottom blade - new blade



Thanks




Sent from my iPhone using Tapatalk

Was searching for new wipers & found this thread. Went with:

- Bosch A980S (Front)
- Bosch A330H (Rear)

Front wipers have arrived & the connector point & serial numbers are different from new to old (pics attached).

Is this not the right blade? Or am I missing something. The connectors are similar in places but are clearly different, didn’t want to force it incase it broke.

Top blade - old blade
Bottom blade - new blade






Sent from my iPhone using Tapatalk

I got some bosch replacements which at first glance seemed fine. In use though they squealed like mad. On looking carefully I noticed that they were slightly loose on the arms and were tiliting backwards and forwards as the sweep direction changed. I bought some genuine ones and you could see (and hear) the difference. Worth looking on ebay to see if any dealers are selling them below full retail. Just make sure they are the real thing though!

PGN wrote:I got some bosch replacements which at first glance seemed fine. In use though they squealed like mad. On looking carefully I noticed that they were slightly loose on the arms and were tiliting backwards and forwards as the sweep direction changed. I bought some genuine ones and you could see (and hear) the difference. Worth looking on ebay to see if any dealers are selling them below full retail. Just make sure they are the real thing though!

Cheers for the response mate. The Bosch ones i picked up don't even seem to want to fit to the arm at all... Originally was going to stick with OEM wipers but couldn't find any at the time...

had a quick look now & still can't seem to see any!

Surely there are alternatives that should work seamlessly & don't have to be VW parts??!

I use the Valeo set VM331 on mine and in my opinion there as good as the Bosch ones. You can pick up a set from EuroCarParts / Carparts4less or any of the online wiper blade suppliers.

Did your rear blade fit OK as I was sure it was a Bosch A251H.

Cuprabob wrote:I use the Valeo set VM331 on mine and in my opinion there as good as the Bosch ones. You can pick up a set from EuroCarParts / Carparts4less or any of the online wiper blade suppliers.

Cheers Bob, will take a look - is the connector the same as the Bosch one? There must be a reason the Bosch set aren’t fitting on to the arm stalk.. They’re the set that I think you recommended higher up the thread but don’t seem to fit on my wiper arms? The existing set are also Bosch but I didn’t fit them so not sure which model they are


Sent from my iPhone using Tapatalk

MR13MOS wrote:

Cuprabob wrote:I use the Valeo set VM331 on mine and in my opinion there as good as the Bosch ones. You can pick up a set from EuroCarParts / Carparts4less or any of the online wiper blade suppliers.

Cheers Bob, will take a look - is the connector the same as the Bosch one? There must be a reason the Bosch set aren’t fitting on to the arm stalk.. They’re the set that I think you recommended higher up the thread but don’t seem to fit on my wiper arms? The existing set are also Bosch but I didn’t fit them so not sure which model they are


Sent from my iPhone using Tapatalk

I'm not sure why yours would be different unless they have changed the fitment as I've used both Bosch 980S and VM331 and not had any issues.

I'm not sure why yours would be different unless they have changed the fitment as I've used both Bosch 980S and VM331 and not had any issues.[/quote]

Me either, I’ll have a look after work & see if it’s just user error.



Sent from my iPhone using Tapatalk

Have you had any joy regarding the fitment?

The back ones I ordered were incorrect, doh.

have ordered the Bosch A251H which look to have the same fitting as my current so hopefully will work fine. Will update once fitted.

No real joy with front wipers either, the connector is a different shape to the current & not sure if it’s just me & my hands are cold but I couldn’t get them to marry up at all. Have contacted Bosch with a picture of the old to see if they can recognise the model.

Found the Valeo pair you mentioned for £20 on carparts4less & considering getting those ordered anyway


Sent from my iPhone using Tapatalk

Yes, the A251H is the correct fitment for the rear. Well it is for mine

Fronts are a bit fiddly to fit but they should just slide in with a click. I assume you are putting the wipers into the "service position" to fit?

Keep us updated if you get to the bottom of it as it's intriguing and may help others in future.

So, i have an update...

A251H fits for the rear
A980S does fit for the front... user error!

Yep, was in 'service position', just wasn't going in at all. Think it's because i was trying to fit it the same way the old one came off - the new connector meant it needed more of an angle to get over the initial connector head & the old arm needed a good clean also.

I spoke to Bosch who told me that, despite the connector looking completely different, the new shape would work with the old arm. It was f***in freezing when i first tried the switch, so a combination of cold fingers, short temper & fiddly bits didn't help...

Once i had the confirmation that it was the right fit and had cleaned the old connector (mine had a lot of gunk inside it which i think was stopping the smooth connection) it was a fairly easy switch. Anyway, got there in the end!

Glad you got there in the end